Petrol Engine Treatment Additive
RVS Technology for Petrol Engines
RVS can improve the fuel economy, endurance, and health of your engine, whether it's a van engine, car engine or motorcycle engine.
The RVS treatment will last for 60,000 miles.
This product range is intended for treating standard Petrol (gasoline) engines. You can read a technical description of RVS products in the ' Technology ' section at the top of the page.
If your car has done LESS than 25,000 miles you can add it to your engine, even in a parking lot: Thoroughly mix the contents of the package together. Add half of the mixture into a warm engine, let the engine idle for 15 minutes, and pour the rest of the mixture into it. Start the engine and drive or let it idle for at least 30 to 40 minutes. That’s how easy it is! More detailed instructions are included in the package.
If your car has done MORE than 25,000 miles we would recommend a double application, this will help clean the engine and allow the product to achieve its maximum efficiency. This will require an application of the RVS treatment, a running-in period, followed by a full engine oil and filter change with a further RVS treatment. More detailed instructions are included in the package.
You can find the oil volume of the engine in the user’s manual of the vehicle or check this site for cars and this site for motorcycles and other vehicles. If the oil volume is more than 9 litres, G4 and G6 products can be combined and used in an engine with an oil volume of 10 litres, two G6 products can be used for treating an engine with an oil volume of 12 litres, etc.
Correspondingly, for treating a 250-cc 2-stroke engine you need two packages of the 2-Stroke 125 product. A 2-stroke engine product can also be divided: with one package of 2-Stroke 125 product, you can treat two 50-cc engines. (Attention! We do not recommend dividing products for treating 4-stroke engines.)
- 2-Stroke 125: For two-stroke 125-cc engines.
- 2-Stroke 500: For two-stroke 500-cc engines.
- G2: For gasoline engines with an oil capacity up to 2 litres.
- G4: For gasoline engines with an oil capacity up to 4 litres.
- G6: For gasoline engines with an oil capacity up to 6 litres.
- G8: For gasoline engines with an oil capacity up to 8 litres.
- GIP3: For gasoline engine injection systems.
Instructions
For engines that have done more than 25,000 miles, It is recommended not to postpone the second treatment further as the dirt removed from the surfaces being treated starts to stick back on the cleaned surfaces.
1st TREATMENT
Less than 25,000 miles / 800 hours
Step 01
Warm the engine up to its normal operating temperature. Meanwhile, squeeze the contents of the small tube into the bottle and close the cap of the bottle and Shake the bottle well (20–30 sec.) until it is well mixed together (The contents of the package should be at room temperature).
Step 02
Pour immediately half of the mixture into the engine and Let the engine idle for 15 minutes.
Step 03
Stop the engine for one minute.
Step 04
Shake the bottle well (20–30 sec.) and Pour the rest of the mixture in the bottle into the engine.
Drive the vehicle at least for 30 minutes avoiding heavy engine loading. When treating a motorcycle engine which incorporates the gearbox, use all the gears for equal intervals during this stage.
Following this, drive the vehicle as usual for approximately 200 - 250 miles ( 300–400 km) but try to avoid heavy engine loading (run-in).
2nd TREATMENT
If more than 25,000 miles / 800 hours
If your engine life has more than 25,000 miles or 800 hours you should perform a 2nd treatment to get the best results. It is recommended not to postpone the second treatment further as the dirt removed from the surfaces being treated starts to stick back on the cleaned surfaces.
It is important to incorporate an engine oil and filter change and then add the 2nd treatment, which is applied in the same way as the 1st treatment.
The treatment is complete after approximately 1500–2000 km (1000–1250 miles) (or 20 to 50 engine hours) counted from the second treatment.
A third treatment with a third package carried out similarly to the first and second ones may be useful for very worn engines.
In The Box
- 150 ml (5.1 oz) of oil
- 11 ml (0.37 oz) of RVS gel
- Step-by-step multilingual instruction booklet
Updating page...